The short version of how to clean double glazed windows is gentler than most people expect: warm water, a mild detergent, a soft cloth, and a squeegee or microfibre finish, working from the top down. That is genuinely it for the glass and the frames. Everything that goes wrong with uPVC maintenance comes from reaching for something stronger, and from forgetting that the seals, drainage channels and hardware need attention too. A few minutes of the right routine twice a year keeps a window working as intended, and that applies as much to double glazed windows and doors as to anything else in the house.
What follows is the method, section by section, along with a clear list of what should never touch a uPVC profile.
What you actually need
Keep the kit simple. Two buckets, one for washing and one for rinsing, a mild dishwashing liquid or a dedicated uPVC cleaner, a few microfibre cloths, a soft bristled brush for corners and channels, a rubber-bladed squeegee, a vacuum with a narrow nozzle, and a light silicone lubricant for hardware. That list handles every window in the house.
The method, top to bottom
Start dry. Vacuum or brush loose dust, grit, cobwebs and insects out of the frame rebate, corners and drainage channels before any water goes near them. Skipping this is how people drag grit across glass and leave a slurry in the channels.
Wash the glass next, before the frames, so dirt running off the pane lands on a frame you have yet to clean. Use warm water with a little detergent, work in sections, and keep the cloth loaded so you float the dirt off rather than scrub it. Rinse with clean water, then squeegee from the top in overlapping strokes, wiping the blade between passes. Finish the edges with a dry microfibre cloth.
Then the frames. The same warm soapy water and a soft cloth suits uPVC. Go gently along the top surfaces where grime collects, into the corners with the brush, and along the glazing bead. Rinse and dry, because detergent residue attracts dust back onto the profile.
Timing matters. Avoid cleaning glass in direct sun, because the water evaporates before you can squeegee it. An overcast day or the shaded side of the house gives a better result.
What to keep away from uPVC
This is the most useful part of the article, so I will be direct. Do not use abrasive cream cleansers, scouring powders, steel wool, scouring pads or melamine sponges on uPVC. They remove the smooth outer surface of the profile, and once that sheen is gone it does not come back. A dulled, scratched surface then holds dirt more readily than the original finish did, so the quick fix creates a long-term problem.
Also avoid solvent-based products: acetone, nail polish remover, methylated spirits, white spirit, paint thinners and strong degreasers can all soften or craze the surface. Keep chlorine bleach off the profiles and seals. Avoid high-pressure washers entirely, because the pressure drives water past seals and can lift gaskets out of their channels. Do not use a razor blade or metal scraper on the glass, particularly where there may be a coating.
If something stubborn is stuck to the profile, such as adhesive residue or paint flecks, start with warm soapy water and patience, then a purpose-made uPVC cleaner, testing anything stronger on a hidden section.
Seals and gaskets
The rubber seals decide whether your window keeps performing, and nobody thinks about them. Wipe them with warm soapy water and a soft cloth when you clean the frames, then dry them. Look for seals that have flattened, shrunk back at the corners, split, hardened or come out of their channel, and press one gently to check it still has give. A seal that no longer compresses is no longer sealing, whatever it looks like.
Keep oils and petroleum-based products off them, because these degrade rubber over time. A silicone-based conditioner applied sparingly once or twice a year keeps gaskets supple, which matters in hot, sun-exposed aspects. Never paint a seal.
Tracks, channels and drainage
Every properly made window system has weep holes or drainage slots along the bottom of the frame to carry incidental water outside. Blocked with dust, pollen or garden debris, they stop draining and water pools in the frame instead. Clear them with the brush and vacuum, then check by trickling a little water into the channel and watching it find its way out.
Sliding panels deserve their own attention, because grit in a track is both a drainage and a wear problem. The rollers run on that track and anything gritty grinds away at both over time, which is why keeping the channel clean matters so much for sliding doors in daily use. Vacuum the full length of the track, wipe it out, and keep it dry rather than greasy, because grease collects the grit you are trying to remove.
Hardware, hinges and locks
Moving parts need two things: cleanliness and the right lubricant. Wipe hinges, handles, locking points and keeps with a damp cloth to lift grime, then dry them. Apply a light silicone or PTFE-based lubricant to hinges, locking cams and keeps, work the handle a few times to spread it, and wipe off the excess. Avoid heavy oils and anything that attracts dust.
Door hardware works harder than window hardware because of how often it is used. Hinges carrying a door leaf through thousands of cycles a year need their fixings checked and their alignment watched, and a latch starting to catch usually means the leaf has shifted slightly rather than that the latch has failed. That is worth keeping in mind for hinged doors, where a small adjustment early prevents the door dragging on its seal and wearing it unevenly. Check too that locking points engage smoothly without force, because forcing a stiff mechanism is how handles and gearing get broken.
A simple schedule
Every few months, wash the glass and vacuum the tracks and channels. Twice a year, do the full routine: glass, frames, seals wiped and inspected, drainage checked, hardware cleaned and lubricated, fixings checked. Once a year, look carefully for seals that have lost compression, misting inside a glass unit, and hinges or locks showing wear. Homes near the coast or on busy roads collect salt and grime faster and benefit from more frequent rinsing.
If you have questions about caring for your windows, or something is not working as it should, the team at uPVC Windows Expert is happy to help. Get in touch and we will point you in the right direction.
Frequently Asked Questions
What do professional window cleaners use to wash windows?
Far less exotic products than people imagine. The standard approach is warm water with a little mild detergent, applied with a soft-bristled applicator or microfibre, then removed with a rubber-bladed squeegee in overlapping strokes, the blade wiped between passes. Some use a water-fed pole with purified water, which dries without spotting because the minerals that cause marks have been filtered out. The result comes from technique and clean tools rather than strong chemicals.
How to get cloudiness out of double-pane windows?
First work out which surface the cloudiness is on. If it wipes off the inside or outside face, it is residue or film, and warm soapy water with a rinse and squeegee will clear it. If it will not wipe off from either side, the haze is sealed inside the cavity, meaning the perimeter seal has failed and humid air has entered the unit. No cleaning method reaches that space, and the unit needs assessing. Exterior hard-water spotting from sprinklers usually responds to a mineral deposit remover used on the glass only, kept away from the frames and seals.
Does vinegar clean glass better than Windex?
Diluted white vinegar in warm water does a perfectly good job on glass. The caveat for double glazed windows is that vinegar is acidic, so keep it off the uPVC profiles, the rubber seals and the hardware, where repeated exposure does no favours. For that reason mild detergent and water is the better everyday choice, since one solution then safely handles glass and frames together. Whichever you choose, the finish depends far more on a clean squeegee and a dry microfibre than on the solution.
How to clean windows that haven’t been cleaned in years?
Work in stages and resist the urge to scrub. Dry brush and vacuum everything first to remove loose grit, cobwebs and insect debris, channels and corners included. Then soak the glass with warm soapy water and let it sit a few minutes to soften the build-up. Wash, rinse and squeegee, expecting to repeat two or three times. Clean the frames and seals separately with fresh soapy water, finish the channels and drainage, then lubricate the hardware. Several gentle passes get you further than one aggressive one.